OK, finally got a configuration that looks like it works:
Address 209.141.39.157
OutboundBindAddress 209.141.39.157
ORPort 209.141.39.157:9001 IPv4Only
ORPort XXX.XXX.XXX.XXX:443 NoListen
ORPort XXX.XXX.XXX.XXX:9001 NoListen
Where XXX.XXX.XXX.XXX is the IP I didn't want to be used by my Tor exit relay. (The IPv4 flag is probably useless, I just didn't think to take it out after adding the IP to the port.)
I'll see if abuse reports for my second IP will stop showing up on abuseipdb.com.
Unless you find I did something wrong, thanks for helping,
Denny
denny.obreham@a-n-o-n-y-m-e.net wrote ..
···
The second IP is still in "Exit Addresses" with the new configuration ... Relay Search
torrc:
Address 209.141.39.157
OutboundBindAddress 209.141.39.157
ORPort 9001 IPv4OnlyDenny
denny.obreham@a-n-o-n-y-m-e.net wrote ..
> Thanks Marco.
>
> First, I had to change my ORPort to 9001 with your proposed configuration because
> using 443 caused an error => "Could not bind to 0.0.0.0:443: Address already
in
> use. Is Tor already running?"
> Probably because my other Tor instance (hidden service) is using it.
>
> Now I'm just waiting for the metrics to update to see if everything is as expected.
>
> Finally, thanks for the help with IPv6 because I cannot get it to work. Somehow
> when I try to check IPv6 availability ( Tor Project | Relay Post-install and good practices
> ), I get "ping6: connect: Network is unreachable". I don't have time to set it
> up right now (I already spent hours last week) so I'll get back to you for that.
>
> Denny
>
> lists@for-privacy.net wrote ..
> > Hi denny,
> >
> > > Hi,
> > >
> > > I just activated my first exit relay. (
> > > Relay Search
> > > 5881B7D4C97C ) I had the following in my torrc (plus some other things):
> >
> > I've answered the rest to the list.
> > If you want to enable IPv6 at Frantech/BuyVM:
> >
> > First create one in Stallion from your given subnet.
> > This is what my /etc/network/interfaces looks like at Frantech
> >
> >
> > # This file describes the network interfaces available on your system
> > # and how to activate them. For more information, see interfaces(5).
> >
> > source /etc/network/interfaces.d/*
> >
> > # The loopback network interface
> > auto lo
> > iface lo inet loopback
> >
> > # The primary network interface
> > allow-hotplug eth0
> > iface eth0 inet static
> > address 104.244.73.43/24
> > gateway 104.244.73.1
> > # dns-* options are implemented by the resolvconf package, if installed
> > dns-nameservers 127.0.0.1 107.189.0.68 107.189.0.69
> > dns-search for-privacy.net
> >
> > iface eth0 inet6 static
> > address 2605:6400:0030:f78b::2/64
> > up ip -6 route add 2605:6400:0030::1 dev eth0
> > up ip -6 route add default via 2605:6400:0030::1
> > down ip -6 route del default via 2605:6400:0030::1
> > down ip -6 route del 2605:6400:0030::1 dev eth0
> > dns-nameservers ::1 IPv6ns1 IPv6ns2
> >
> >
> > --
> > ╰_╯ Ciao Marco!
> >
> > Debian GNU/Linux
> >
> > It's free software and it gives you freedom!